Search Results

The environmental and sustainable energy concerns in transport are being addressed through the decarbonisation path and the potential of hydrogen as a zero-carbon alternative fuel. Using hydrogen to replace fossil fuels in various internal combustion engines shows promise in enhancing efficiency and achieving carbon-neutral outcomes. This study presents an experimental investigation of hydrogen (H2) combustion and engine performance in a boosted spark ignition (SI) engine. The H2 engine incorporates both port fuel injection (PFI) and direct injection (DI) hydrogen fuel systems, capable of injecting hydrogen at pressures of up to 4000 kPa in the DI system and 1000 kPa in the PFI operations. This setup enables a direct comparison of the performance and emissions of the PFI and DI operations. The study involves varying the relative air-to-hydrogen ratio (λ) at different speeds to explore combustion and engine limits for categorising and optimising operational regions.

Churning loss is an important energy loss term for rolling bearings at high-speed condition. However, it is quite challenging to accurately calculate the churning loss. A CFD study based on unsteady Reynolds-Averaged-Navier-Stokes that resolves the gas-liquid interface was performed to examine the unsteady multiphase flow in a roller/ball bearing. In this study, the rotating motion of the cage, races, rollers/balls about the shaft as well as self-rotation of rollers/balls about their own axis were accounted to accurately predict the oil distribution in various parts of the bearings. A novel meshing strategy is presented to resolve thin gaps between the roller/balls and the races/cage while preserving the shape of balls/rollers, races and cage. Five rotational speeds of the shaft have been examined for roller bearing and ball bearing respectively. Additionally, effect of clearance between roller/balls and races is investigated.

Ensuring spray robustness of gasoline direct injection (GDI) is essential to comply with stringent future emission regulations for hybrid and internal combustion engine vehicles. This study presents experimental and numerical assessments of spray for lateral-mounted GDI sprays with two different plume arrangements to analyze spray collapse characteristics, which can significantly deteriorate the atomization performance of fuel sprays. Novel spray characterization methods are applied to analyze complex spray collapse behaviors using diffusive back-illuminated extinction imaging (DBIEI) and 3D computed tomographic (CT) image reconstruction. A series of computational fluid dynamics (CFD) simulations are performed to analyze the detailed spray characteristics besides experimental characterization. Spatio-temporal plume dynamics of conventional triangle-pattern spray are evaluated and compared to a plume pattern with an inversed T pattern that has more open space between plumes.

Lean-burn hydrogen internal combustion engines are a good option for future transportation solutions since they do not emit carbon-dioxide and unburned hydro-carbons, and the emissions of nitric-oxides (NOx) can be kept low. However, under lean-burn conditions the combustion duration increases, and the combustion stability decreases, leading to a reduced thermal efficiency. Turbulent jet ignition (TJI) can be used to extend the lean-burn limit, while decreasing the combustion duration and improving combustion stability. The objective of this paper is to investigate the feasibility of a passive pre-chamber TJI system on a heavy-duty hydrogen engine under lean-burn conditions using CFD modelling. The studied concept is mono-fuel, port-fuel injected, and spark ignited in the pre-chamber. The overall design of the pre-chamber is discussed and the effect of design parameters on the engine performance are studied.

The European Union aims to be climate neutral by 2050 and requires the transport sector to reduce their emissions by 90%. The deployment of H2ICE to power vehicles is one of the solutions proposed. Indeed, H2ICEs in vehicles can reduce local pollution, reduce global emissions of CO2 and increase efficiency. Although H2ICEs could be rapidly introduced, investigations on hydrogen combustion in ICEs are still required. This paper aims to experimentally compare a flat piston and a bowl piston in terms of performances, emissions and abnormal combustions. Tests were performed with the help of a single cylinder Diesel engine which has been modified. In particular, a center direct injector dedicated to H2 injection and a side-mounted spark plug were installed, and the compression ratio was reduced to 12.7:1. Several exhaust gas measurement systems complete the testbed to monitor exhaust NOx and H2.

In electric-powertrains, noise and vibration can be generated by components such as gears and motors. Often a noise phenomenon known as rumble or droning noise can occur due to low shaft order excitation at the spline. In this study, we identified the excitation source for spline induced rumble noise and developed a novel analysis method. First, a detailed spline model, believed to be the key factor for rumble noise, has been developed and verified by comparison with Finite Element Method(FEM) analysis. In order to identify an excitation source, a typical electric-powertrain assembly model including the developed spline model was constructed and simulated. Results according to changes of key factors including spline pitch errors and shaft alignment errors were analyzed. Spline radial force has been identified as an excitation source of spline induced rumble noise. This was verified through comparison with the forced vibration analysis result and time domain analysis result.

With the rapid development of electric vehicles (EVs), lithium-ion batteries (LIBs) with high energy and power density have been widely applied as the power producer of EVs. However, the range of EVs has been criticized. To meet consumer demand for high power and long driving distances, the energy and power density of LIBs are getting higher and higher. However, LIBs with higher energy density are more prone to catastrophic thermal runaway (TR). In recent years, EV accidents due to TR of LIBs have been frequently reported, which makes consumers lose confidence in EVs. To solve the problem, we must understand the mechanism of LIBs TR, thereby reducing the likelihood of TR in EVs. However, the induction mechanism of LIB TR induced by mechanical abuse is sophisticated. This paper focuses on recent advances in the study of thermal TR characteristics of batteries caused by mechanical abuse, including bending, collisions, and penetration.

As the automotive industry accelerates its virtual engineering capabilities, there is a growing requirement for increased accuracy across a broad range of vehicle simulations. Regarding control system development, utilizing vehicle simulations to conduct ‘pre-tuning’ activities can significantly reduce time and costs. However, achieving an accurate prediction of, e.g., stopping distance, requires accurate tire modeling. The Magic Formula tire model is often used to effectively model the tire response within vehicle dynamics simulations. However, such models often: i) represent the tire driving on sandpaper; and ii) do not accurately capture the transient response over a wide slip range. In this paper, a novel methodology is developed using the MF-Tyre/MF-Swift tire model to enhance the accuracy of ABS braking simulations.

Internal combustion engine (IC engine) vehicles are commonly used for transportation due to their versatility. Due to this, efficiency in design process of IC engines is critical for the industry. To assess performance capabilities of an IC engine, thermal predictions are of utmost consequence. This study describes a computational method based on unsteady Reynolds-averaged Navier–Stokes equations that resolves the gas–liquid interface to examine the unsteady single phase/multiphase flow and heat transfer in a 4-cylinder Inline (i-4) engine. The study considers all important parts of the engine i.e., pistons, cylinder liners, head, block etc. The study highlights the ease of capturing complex and intricate flow paths with a robust mesh generation tool in combination with a robust high-fidelity interface capturing VOF (Volume-of-Fluid) scheme to resolve the gas-liquid interfaces.

Leveraging the power of math models in driveline development requires a deeper appreciation for the multi-disciplinary and wide ranging physical system dynamic behaviors involved. The models have to handle operational demands of multi-configurable systems brought on by hybrid powertrains in general and automatic/manual transmissions, specifically. As a first requirement, system models have to be broken down into physically compatible subsystems, not as the hardware looks but, as the interface dynamics suggest. Transient dynamics, brought on by subsystem power flow disturbances and attendant noise generation and controls challenges must be addressed up front. This paper delves into the levels of detail automotive propulsion system models must possess not only to offer insight to the inner dynamics of a product but, also, make such formulation compatible with modern control system techniques.

This paper outlines the methodology to 1) determine what leak rate specification is appropriate for a given automotive component, 2) arrive at the gas-based leak test method that is best suited for the situation, and 3) perform the requisite calculations to confirm the choice of test method. Also provided are summary tables (based upon actual industry experience) relating component type, typical leak rate specification, test method used, and (production) sensitivity range of the method utilized.

There have been a number of papers written about the dynamic effects of low speed front to rear impacts between motor vehicles during the last several years. This has been an important issue in the field of accident analysis and reconstruction because of the frequency with which the accidents occur and the costs of injuries allegedly associated with them. Several of these papers have discussed the importance of the coefficient of restitution in the accelerations and speed changes that the vehicles undergo in such impacts. These discussions often include data showing the measured restitution for impacts involving various bumper types and closing speeds. However, in most of these studies, the impacts are controlled so that direct bumper to bumper impacts occur. This paper will present the results of several rear impact tests with non-standard impact configurations.

This paper examines the effect that test barriers currently used for frontal and side impact tests have had on collision compatibility between different-sized vehicles. The peak force levels generated by the vehicles’ front structures are one of the significant factors in determining vehicle compatibility. It is shown from principles of mechanics that the use of fixed barriers as a test device may lead to higher force levels for front ends of larger vehicles and thus increase the incompatibility between large and small vehicles. Review of data from various sources supports this conclusion that the peak force levels of vehicles’ front ends have increased in proportion to their test mass. Available crash data is also examined for a relationship between NCAP ratings of vehicles and the likelihood of serious and fatal injuries to occupants of those vehicles. These data do not show any relationship between the frontal NCAP ratings of vehicles and their rate of serious or fatal injuries.

The evasive capabilities of motorcycles and riders are often an important consideration when analyzing a motorcycle crash. Specifically, the longitudinal distance or time required for a motorcycle to move laterally some distance can be of critical interest. Previous publications on this topic have not all measured the same thing and have often included limited test data so their results can be difficult to compare or apply. In addition to reviewing some of the literature on the topic, this paper will present the results of a series of tests conducted with four riders on four motorcycles swerving 2 m (6.5 ft) to their left after passing through a gate at speeds of 40 to 88 km/h (25 to 55 mi/h). The most recent testing involved relatively skilled riders who had faster transitions and greater willingness to lean than the “average” rider generally described in the literature.

Over the years, natural gas has been promoted as a clean-burning fuel, especially for transit buses. A decade ago one could claim that natural gas buses deliver significant emission benefits over diesel buses, especially regarding particulate emissions. The spread in nitrogen oxide emissions has always been significant for natural gas engines, high for lean-burn engines and low for three-way catalyst equipped stoichiometric engines. With the introduction of US 2010 and Euro VI (effective as of 2014) exhaust emission regulations, independent of the fuel, the regulated emissions of all engines have been brought close to zero level. This means that the advantage of natural gas as a clean fuel is diminishing, especially in a situation in which electric transit buses are also entering the market. The motivation to use natural gas could still be diesel fuel substitution and to some extent, also reduction of greenhouse gas emissions.

Computer Aided Engineering (CAE) plays an important role in the product development. Now a days major decisions like concept selection and design sign off are taken based on CAE. All the Original Equipment Manufacturers (OEMs) are putting consistent efforts to improve accuracy of the CAE results. In recent years confidence on CAE prediction has been increased mainly because of good correlation of CAE predictions with the test results. Defining proper correlation criteria and using a systematic approach helps significantly in building the overall confidence level for predictions given by CAE simulations. Representation of manufacturing effects on material properties and material failure in the simulation is still a big challenge for achieving a good CAE correlation. This paper describes side impact test vs CAE correlation. The important parameters affecting the CAE correlation were discussed.

One of the critical items for a good matching between CAE predictions and actual hardware data is the input parameters variability. A vehicle component, for example, after manufactured shows imperfections that can be translated in small variation on nominal values of geometries and material properties. These variations of physical and geometrical parameters, fundamental data to construct a numerical model, cause impact on dynamic response. Analysis of this impact requires the use of appropriate stochastic methods for structural problems, mainly in correlation analysis between numerical and experimental results. This work assesses Body-in-White Point Mobility and Vibration Transfer Function correlation between CAE predictions and actual vehicle performance, including production variation and test uncertainty data.

Based on BF6M1015CP electronic diesel engine (it is a supercharged, water-cooled engine. It has 6 cylinders and it is for heavy-duty vehicle) and HD4070PR electronic automatic transmission (it covers heavy-duty applications requiring high input horsepower and torque. It contains torque converter module, control module, planetary module and output module. It has 7 forward gears and a power-take -off (PTO) and a retarder), the paper analyzes the shift system of an electronic automatic transmission and sets up a mathematic module of the shifting process. With the model the shifting process is analyzed and the model can be used directly in shifting process control, and the rules of shifting process can be derived. To improve the shift quality, in the paper the different control methods in different phases are used and reviewed that Include the open-loop control, fixed ramp rate, and closed-loop control.

Bollard systems are often used to separate errant vehicular travel from pedestrian and bicycle traffic. Various bollard systems are available for this function, including different installations, functional design, and protection levels. The security-type bollards are used primarily at high-security locations (e.g., military bases and other government installations) around the world. While a protocol exists for testing and rating security bollards, no such protocol or recommended practice or standard currently exists for non-security-type bollards. Non-security, concrete-filled bollards are commonly used by cities/states, local government organizations, and the private sector as “perceived impediments to access” to protect against slow-moving vehicles. There is a general lack of publically available test data to evaluate these non-security bollards and conventional installation procedures.